Home / Arduino / 14 Tips to improve Arduino Schematic and PCB

14 Tips to improve Arduino Schematic and PCB

Here are couple of tips which you may want to consider when you will be designing your own Arduino Uno like board.

TIP 1: Micro USB connector

Today, everybody uses micro USB cables, chargers or power supplies. Some adapters can deliver quite high currents, for example up to 2A – that really can be sometimes useful.

TIP 2: Reset

RESET is one of the most important pins on microcontroller. Be sure you deliver stable and strong signal to this pin. Otherwise you may experience random or unreliable board resets. (See recommended RESET signal connection in the AVR042: AVR Hardware Design Considerations)

TIP 3: Decoupling & Filtering Power

Usually, every microcontroller power pin should have its own decoupling capacitor (e.g. 100nF). If the microcontroller has an analog circuit inside (e.g. AD converter) and you use it, you may want to separate analog power pins from digital power pins through Ferrite BEADS.

In the case there is a power pin on a connector (e.g. +5V, +REF, …), consider placing a capacitor close to the pin. If it’s a power output pin, use a bigger capacitor (e.g. 10-330uF), if it’s an input power pin, use something smaller, e.g. 100nF.

TIP 4: Series termination resistors

Microcontrollers are not very fast, but the buffers are quite quick (e.g. SPI rise/fall time is 3.6 ns). You may want to add 22 or 33 OHM series termination resistors into signals like Clocks.

TIP 5: 5V/3V3 support

Most of todays electronic uses 3.3V IO voltage. Both microcontrollers can support it.

TIP 6: Firmware update

In the case you need to re-flash the ATMEGA328P (including bootloader), it can not be done easily without using an external programmer. And it is not difficult to do, as there is everything on the board you need. You can easily re-program the ATMEGA16U2 with AVRISP MKII firmware and add couple of tracks.

TIP 7: Programmer

If your board is properly designed, you not only can use the ATMEGA16U2 to program the on board ATMEGA328P, but you can use it as a standard AVRISP MKII programmer.

TIP 8: Connector pinout

Each connector should have at least one GND pin, including analog connectors. Also, I would really add a power pin to the IOH header, because in many cases and examples I would only need to connect this one connector. In the current design, we always have to connect at least two connectors.

And I would move the REF voltage to the Analog connector.

TIP 9: Solid Ground

When you are doing layout, try to keep the ground plane as solid ans as large as possible.

TIP 10: Gap between tracks

For 2 Layer PCBs is very important you keep as big gap as possible between the tracks. Especially, if the tracks are CLOCKs.

TIP 11: Simple board shape

I know the creators of Arduino intentionally designed the board shape as we know it. The thing is, it makes your PCB more expensive. The PCB manufacturer will need to use a milling machine – that is one more step in PCB manufacturing process.

TIP 12: Mounting holes

It is good to keep a bigger clearance or use bigger pads around mounting holes, so when you tight up screws, you don’t damage or don’t make a short circuit with tracks.

TIP 13: Pin 1 and connector marking

There is very nice silkscreen on the Arduino, but the things like Pin 1 or connector reference designators are missing. If you want to identify them, you have to use Arduino schematic or PCB files.

TIP 14: Connector placement

When you place a connector on your board, be sure you can plug in the mates.

Have a look how we implemented all these points in our open source 28Pins board. Feel free to download the full documentation, including Schematic, PCB, BOMs, GERBERs and all the manufacturing files here >>>

Learn to Design Your Own Boards Online – Based on Arduino

After this course, you will design your own Arduino like board. This course is for everyone who has never designed any board before and would like to try it.

How to register for this online course?

Step 1: Register & Login at FEDEVEL Academy website – Click here
Step 2: Select your course (you will need to be logged in) – Click here

Find out more about this course in this short introduction video


Learn Advanced PCB Layout ONLINE

You will learn how to do Advanced PCB Layout (DDR3, PCIE, SATA, Ethernet, etc.).

How to register for this online course?

Step 1: Register & Login at FEDEVEL Academy website – Click here
Step 2: Select your course (you will need to be logged in) – Click here

Find out more about this course in this short introduction video


Learn Advanced Hardware Design ONLINE
Starting next week. Don’t miss. Register here >>
Special offer THIS WEEK ONLY: Sign up for Advanced Hardware Design Course and Get FREE Altium Essentials Online Course Register here >>

This course will show you how you can design boards more effectively and produce professional results. It provides you tips and tricks to help you to design boards that work the first time.

The course is practically based and will teach you everything by actually doing it. Anyone who is interested can work on his/her own project during the course. By the end of the course you will have learnt how to create professional manufacturing output which you can then use to build your own board.

How to register for this online course?

Step 1: Register & Login at FEDEVEL Academy website – Click here
Step 2: Select your course (you will need to be logged in) – Click here

Find out more about this course in this short (2 minutes) introduction video

Check Also

079fi

TIP #079: Name every important net in your schematic, even if …

TIP #079: Name every important net in your schematic, even if it connects only 2 …